High-build epoxy satin coating for all types of surfaces. The advantage to build up a thickness of 100-150 dry microns per coat allows sensible reduction of labour costs. Overcoatable with chlorinated rubber, epoxy or polyurethane coatings for high quality long lasting anticorrosive coating systems. Provides outstanding chemical resistance in the marine environment, both in atmosphere or immersion conditions. Excellent as anti-osmosis pre-treatment on fibreglass boats.
SURFACE PREPARATION AND APPLICATION PROCEDURE
Steel. Sandblasting according to SA 2,5 is recommended. If sandblasting is not possible, the substrate should be cleaned perfectly, degreased, free from traces of corrosion and mechanically sanded. In case of pre-existing epoxy, polyurethane or zinc-based undercoats in good conditions overcoat with 1 coat of EPOFOND HB followed by 1-2 coats of POLIFOND Primer, allowing the required waiting time between coats. Overcoat then with the recommended topcoat.
Bare Galvanized Steel. The surface should be clean, dry and well degreased. Apply 1 coat of EPOFOND HB as suggested.
Previously Painted Galvanized Steel. Remove any trace of corrosion by sanding. The surface should be clean, dry and well degreased. Apply 1 coat of EPOFOND HB as suggested
Fibreglass. The surface should be dry, degreased and slightly sanded with fine abrasive paper. Apply 1 coat of EPOFOND HB as suggested.
Cement. The surface should be clean, dry, well seasoned and free from loosing particles. Apply 1 coat of EPOFOND HB as suggested.
| Paint Type | Two components |
| Binder type A | Epoxy |
| Binder type B | Ammine adduct |
| Specific gravity kg/lt (±0,05) | 1,460 (A) - 1,020 (B) |
| Solids content (weight) ±2 | 75% |
| Solids content (volume) ±2 | 45% |
| Viscosity Ford ø 8 at 20°C ±2 | Tixotropico (A+B) |
| Shelf life +23°C (±2) | 30 months in unopened cans |
| Viscosity Ford (Ø4 a 20°C) | Tixotropic (A+B) |
| Application | Brush-Roller-Spray |
| Mixing ratio A+B by volume | 4 parts Sol. A with 1 Sol. B |
| Mixing ratio A+B by weight | 100 parts Sol. A with 16 Sol. B |
| Pot life A+B (20°C) | use within 6-8 hours |
| Brush-Roller | 10-15% Thinner 765 |
| As a primer on bare wood* | 15-20% Thinner 765 |
| Spray | 15-20% Diluente 765 |
| Touch dry | 2-3 h (20°C) |
| Recoat time | 12-24 h (20°C) |
| Application temperature | Between +10 C and +40 C |
| Relevant humidity | Less than 80% |
| Dry film thickness advised | 150 microns per coat |
| Theoret. coverage m2/Lt | 4-5 (3-4 m2/kg) |
Colors: BIANCO
Color code: 5G1145
Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.
The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.
Seguici su
Tel:
Fax:
Email -
PEC -
© Aemme Colors 2022 - All rights reserved.
Cookie Policy - Privacy Policy