Serenissima

Serenissima

pdf-icon

Code: 3F

High quality, long lasting idrophilic matrix antifouling paint. The high content of coprous oxide and other valuable additives, combined to the particular vehicle formulation, allow this product to provide an excellent antifouling power in the most varied conditions. The hydropfilic nature of the vehicle improves wettability and flowing characteristics of the hull in the water. It can be effectively used also in warm seas and miscellaneous water. Provides a controlled speed release of the antifouling salts which makes this product recommended on both medium speed boats and sailing boats. Not suitable on aluminium boats. Recommended for boats with speed up to 30 knots. The application of 2 coats is recommended,

SURFACE PREPARATION AND APPLICATION PROCEDURE
Bare Steel bottom. Apply 1 coat of  EPOFOND AM-9 on sandblasted steel according to SA 2,5/3 and let dry for 12-24 hours. (If sandblasting is not possible proceed with mechanical cleaning to bring the surface to bare steel, apply 1 coat of EVIOX CROMOMINIO and let dry for 8-12 hours.) Apply then 3 coats of SOLVER PRIMER allowing 24 hours between coats. Overcoat twith 2-3 coats of SERENISSIMA antifouling allowing min.8 hours between coats.
Bare Wood bottom. Apply one coat of EVIOX CROMOMINIO and allow to dry for 8-12 hours. Apply 2 coats of SOLVER PRIMER allowing 24 hours between coats followed by 2-3 coats of SERENISIMA antifouling allowing min. 8 hours between coats.
Fibreglass bottom. Degrease with detergent solution and rinse with water. Light sanding with fine abrasive paper and apply 1 coat of POLIFIBER PRIMER. Allow 24 hours before sandpapering with fine abrasive paper. Overcoat then with 2-3 coats of SERENISSIMA antifouling allowing min.8 hours between coats.
Previously Coated Boat Bottom. If the old antifouling is in good conditions apply 2 coats of SERENISSIMA after light sandpapering. If the old antifouling is unknown, a patch test on a small area is necessary to check the compatibility with the new antifouling. If this is okay, sandpaper with fine abrasive paper and apply 2 coats of SERENISSIMA. In case some tiny bubbles are experienced during the patch test, apply  one coat of SOLVER PRIMER in order to insultate the old paint layer. Apply 2-3 coats of SERENISSIMA antifouling allowing min. 8 hours between coats. It is however recommended that every 3 or 4 years of repainting the old paint layers should be completely removed.

*Note 1. Brush application. The antifouling should be applied by longitudinal movement with respect to waterline. Wait minimum 8 hours before applying the second coat. A third coat of SERENISSIMA should be preferably applied on the waterline and on the rudder.

Recommendations. After the application of the last coat the maximum launching period of the antifouling is 1 month; with top quality copper based antifouling and after agreement with our technical staff, the launching time may extend up to 3 months, providing that the hull is protected from moisture, rain or atmospheric agents with plastic cover or similar material.

Colour. The color of the antifouling paint after immersion in water may result slightly different since small color differences can occur between different production lots: if necessary, mix them before application.

Remarks. The values specified in the present technical data sheet may vary slightly  from one batch to another. The antifouling paint must not come in contact with water, chemicals or subjected to mechanical stress before the curing is complete. The wet film thickness refers to the undiluted product. In case of dilution, this value increases. The above information is the result of accurate laboratory tests and practical experience, however, since the product is predominantly used outside the manufacturer's control, we can only guarantee the continuous quality of the product. The above information may  be subject to revision by our company. For clarification, updates or further information, it is recommended to contact our company directly. This technical data sheet cancels and replaces any other previously published data sheet.

Paint Type One component
Binder type A Synthetic copolymer - Hydrogenated resin
Specific gravity kg/lt (±0,05) 1,80-1,90 according to colour
Solids content (volume) ±2 38%
Viscosity Ford ø 8 at 20°C ±2 12-15 sec.
Shelf life +23°C (±2) 36 months in unopened cans
Application Brush-Roller-Spray
Brush-Roller Ready to use or max 5% Thinner 400
Spray 10-15% Thinner 400
Touch dry 1-2 h (20°c)
Launching time Min 24-48 hours
Recoat time 8-12 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 40-50 microns per coat
Theoret. coverage m2/Lt 8-10

Colors: NERO
Color code: 3F6847

Colors: AZZURRO
Color code: 3F6852

Colors: BLU SCURO
Color code: 3F6842

Colors: ROSSO OX
Color code: 3F5745

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.