Hard matrix type antifouling containing mainly copper oxide. Its water-based formulation, therefore odorless and ecological, makes it an innovative product in the sector. The hard matrix allows its film once in contact with water to be always active with the movement of the boat. We recommend applying a minimum of 3 coats for optimal results. The duration and antifouling effect varies with the speed and operation of the boat. A light sanding is sufficient when repainting. Recommended for boats with medium speed even over 30 knots. The product is also particularly suitable for the protection of fishing nets. Not suitable for aluminum hulls.
PREPARATION OF THE SUPPORT AND APPLICATION CYCLE
New iron hulls. Apply a coat of EPOFOND AM-9 on sandblasted iron to SA 2.5 (*) and let it dry for 12-24 hours. Then apply 1-2 coats of SOLVER PRIMER at intervals of 24 hours between them. Overpaint with 2/3 coats of POSEIDON-AQUA antifouling at least 12 hours apart.
(*) If it is not possible to carry out sandblasting, it is advisable to mechanically restore the iron to new condition; clean the surface and apply 1 coat of CROMOMINIO-AT leaving it to dry for 8-12 hours. Then apply 2-3 coats of SOLVER PRIMER at intervals of 24 hours between them. Overpaint with 2/3 coats of POSEIDON-AQUA antifouling at least 12 hours apart.
New wooden hulls. Apply a coat of CROMOMINIO-AT and let it dry for 8-12 hours. Apply 2 coats of SOLVER PRIMER 24 hours from each other, then 2/3 coats of POSEIDON-AQUA antifouling at least 12 hours apart.
New hulls in fiberglass or plastic. Degrease with detergents and water and rinse. Lightly sand with fine abrasive papers and dust. Apply a coat of UNIFIBER PRIMER / EPOFOND AM-9 and after 24 hours sand with fine sandpaper. Then apply 2/3 coats of POSEIDON-AQUA antifouling at least 12 hours apart.
| Shelf life min+10°C max+35°C | 36 months in unopened cans |
| Paint Type | Water-based one-component paint |
| Binder type A | Natural resins modified, Resins-Acrylic copolimers |
| Specific gravity kg/lt (±0,05) | 1,700 /1,800 |
| Solids content (volume) ±2 | 43% |
| Viscosity Ford ø 8 at 20°C ±2 | 13-15 sec. |
| Application: by spreading | Ready to use, possibly 3-5% water |
| Application: Spray | Brush - roller - spray |
| Drying time | 1-2 hours (20 ° C) |
| Recoat time | Min 12 hours (20 ° C) |
| Application temperature | Between +10 C and +40 C |
| Relevant humidity | Less than 80% |
| Dry film thickness advised | 40-50 microns per coat for a total run of 120-150 microns dry in 3 coats |
| Theoret. coverage m2/Lt | 9-10 |
Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.
The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.
Seguici su
Tel:
Fax:
Email -
PEC -
© Aemme Colors 2022 - All rights reserved.
Cookie Policy - Privacy Policy