Sirena ABR

Sirena ABR

pdf-icon

Code: A671

It is a special self-polishing antifouling based on copper oxide and non-polluting components withstanding seaweed growth. The synthetic copolymers of the binder used for the formulation of this antifouling gives the product a controlled release of the antifouling salts throughout its service. With a dry film thickness of 120 microns the antifouling duration can vary from a minimum of 12 months to a maximum of 16 months. It is applied onto steel, fibreglass and wooden boats with a speed up to approx. 20-25 knots.

SURFACE PREPARATION AND APPLICATION SYSTEM

Bare steel. The substrate should be sanblasted or accurately wirebrushed and well degreased. Apply a first coat of EPOFOND AM-9.  Let dry and follow up with 2 coats of EPOFOND AM-9 and then 1 coat of SOLVER PRIMER. Overcoat then wit h 2-3 coats of SIRENA ABR antifouling, always allowing the required drying time between coats.

Bare wood.
Apply 1 coat of EVIOX CROMOMINIO followed by 2 coats of SOLVER PRIMER. Overcoat then with 2-3 coats of SIRENA ABR antifouling, always allowing the required drying time between coats.

Fibreglass (gelcoat).
Apply over the gelcoat 1 coat of UNIFIBER PRIMER followed by 2-3 coats of SIRENA ABR antifouling, always allowing the required drying time between coats.

Painted hull.
The bottom surface should be perfectly cleaned, free from fouling, rinsed with fresh water and sanded ( wet sandpapering is recommended) wear protective mask and googles during application to avoid contact with dust particles). Apply over the old antifouling (especially if the nature is unknown) 1 coat of SOLVER PRIMER as intermediate coat, followed by 2 coats of SIRENA ABR, always allowing the required drying time between coats.


Recommendations. After the application of the last coat the maximum launching period of the antifouling is 1 month; with top quality copper based antifouling and after agreement with our technical staff, the launching time may extend up to 3 months, providing that the hull is protected from moisture, rain or atmospheric agents with plastic cover or similar material.

Colour. The color of the antifouling paint after immersion in water may result slightly different since small color differences can occur between different production lots: if necessary, mix them before application.

Remarks. The values specified in the present technical data sheet may vary slightly  from one batch to another. The antifouling paint must not come in contact with water, chemicals or subjected to mechanical stress before the curing is complete. The wet film thickness refers to the undiluted product. In case of dilution, this value increases. The above information is the result of accurate laboratory tests and practical experience, however, since the product is predominantly used outside the manufacturer's control, we can only guarantee the continuous quality of the product. The above information may  be subject to revision by our company. For clarification, updates or further information, it is recommended to contact our company directly. This technical data sheet cancels and replaces any other previously published data sheet.

Paint Type One component
Binder type A Synthetic copolymers
Specific gravity kg/lt (±0,05) 1.680-1.720 depending on the colour
Solids content (volume) ±2 50%
Viscosity Ford ø 8 at 20°C ±2 12-18 seconds
Shelf life +23°C (±2) 36 months in unopened cans
Application Brush-Roller
Brush-Roller Ready to use or max 5% Thinner 400
Spray 10-15% Thinner 400
Touch dry 2-3 h (20°c)
Launching time Min 24-48 hours
Recoat time 8-12 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 40 microns per coat
Theoret. coverage m2/Lt 8-10

Colors: ROSSO OX
Color code: A67114

Colors: BLU SCURO
Color code: A67128

Colors: NERO
Color code: A67170

Colors: AZZURRO
Color code: A67122

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.