Micox

Micox

pdf-icon

Code: 2N & 2T

Based on the formulation of the already known and appreciated SINTOLIN enamel, combines ease of application with good anticorrosion properties thanks to the characteristics of its ingredients. The lamellar structure of the pigments used in its formulation (based on micaceous iron oxides) reflects the majority of ultraviolent rays (which are the main cause of chalking) and forms a resistant barrier against moisture, thus protecting the metal substrate from its main enemy: corrosion. These properties make of MICOX a finishing product for "direct application" on well prepared steel and iron surfaces, protecting them for long time and giving an attractive finish. It is always necessary to apply two coats of product in order to obtain a reliable coverage of the substrate. In addition to its anticorrosion properties MICOX gives a pleasant metalized finish, widely used on wrought iron, gates, bars etc.

SURFACE PREPARATION AND APPLICATION
STEEL/IRON
Bare substrate.
If sandblasting is not possible, remove all traces of corrosion by mechanical wirebrush or sanding disk. Dust off, degrease the substrate with Thinner 107 or 900. Apply 1-2 coats of MICOX allowing the required waiting time between coats.

Painted surfaces.
Remove any loose or powdery paint with a scraper. Remove trace of corrosion with a mechanical wirebrush or sanding disk and sandpaper the surface with medium abrasive paper (280-320). Dust off and degrease the surface with Thinner 107 or 900. Apply as soon as possible one coat of MICOX onto the bare areas. Let dry and apply 1-2 coats of MICOX allowing the required waiting time between coats. 
Wood.
Bare substrate.
Onto dry, clean and well seasoned wood apply a first coat of LIGNUM IMPREGNANTE and let dry for 3-4 days. Apply 1-2 coats of MICOX allowing the required waiting period between coats.
Painted surfaces. Remove any loose or powdery paint with a scraper and sandpaper with medium abrasive paper (280-320). Degrease with suitable detergent product and let dry. Apply 1-2 coats of MICOX allowing the required waiting time between coats.

Paint Type One component
Binder type A Alkyd
Specific gravity kg/lt (±0,05) 1.100-1.550 depending on the colour
Solids content (weight) ±2 75%
Viscosity Ford ø 8 at 20°C ±2 40
Shelf life +23°C (±2) 30 months in unopened cans
Note Store in a cool and dry place. Do not store at low temperatures.
Application Brush-Roller-Spray
Brush-Roller 5-10% Thinner 107
Spray 10-15% Thinner 900
Dust dry 3-4 hours
Recoat time 24 h
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 40 microns per coat
Theoret. coverage m2/Lt 10-12

Colors: MICOX ARDESIA LUCIDA
Color code: 2TA0000

Colors: MICOX ARDESIA
Color code: 2NA0000

Colors: MICOX ARGENTO LUCIDO
Color code: 2TE0000

Colors: MICOX ARGENTO
Color code: 2NM0000

Colors: MICOX BRONZO
Color code: 2ND0000

Colors: MICOX SILICEO LUCIDO
Color code: 2TF0000

Colors: MICOX SILICEO
Color code: 2NC0000

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.